Baudouin 12M26 Series Operation And Maintenance Manual Download Page 43

Page: 43 / 83

O&M Manual for PowerKit M26 Series Diesel Engine

5. Maintenance

5.1 General Safety Conditions for Maintenance

SAFETY WARNING

Users should carefully read the safety instructions before installation and operation of the en-

gine.

Electrical insulation controls must NOT be done with a voltage higher than 50VDC

Safety conditions for preventive and corrective maintenance operations are intended to

check.



Engine and generator alignment.



The tightness of the entire engine unit on the frame.



The tightness of the couplings and all elements transmitting power.



The isolation and condition of electrical equipment.



The condition and tightness of electrical connections.



Control of oil, fuel and coolant levels.



Operation of the alarm safety devices.



Replacement of oil, fuel and air filters.

Summary of Contents for 12M26 Series




















































































Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands

Baudouin 12M26 Series, Operation And Maintenance Manual

Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands