601–426 /15
F70 Series
14
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified
service personnel before resuming operations.
•
Do not disassemble this projector, always take it to an authorized trained service person when service or
repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device
due to lightning and AC power-line surges.
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before
connecting to the wall outlet or adjusting the projector.
•
To prevent injury, take note of the weight of the projector.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the
eye.
•
Warning: extremely high brightness laser: This projector uses extremely high brightness laser. Never
attempt to look directly into the lens or at the laser.
•
Always switch off the projector and disconnect from the mains power supply before attempting to remove
any of the projector covers or access parts inside the projector.
•
This product contains no user serviceable parts except the Color Wheel. Attempts to modify/replace
mechanics or electronics inside the housing or compartments will violate any warranties and may be
hazardous.
•
Do not remove/replace any other parts than the Color Wheel. Other parts, service personnel only Warranty
void if removed
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious
damage to it and possible injury to the user.
•
Only place the projector on a stable surface, or mount it securely using an approved ceiling-mount.
•
It is hazardous to operate without lens or lens cap. Lenses or shields shall be changed if they have
become visibly damaged, for example with cracks or deep scratches, to such an extent that their
effectiveness is impaired.
To prevent fire hazard
•
Barco projection products are designed and manufactured to meet the most stringent safety regulations.
This projector radiates heat on its external surfaces and from ventilation ducts during normal operation,
which is both normal and safe. Exposing flammable or combustible materials into close proximity of this
projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is
absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no
flammable or combustible materials are present. The exclusion zone in the exhaust area must be not less
than 100 cm (40”). The exclusion zone on the intake area must not be less than 50 cm (20”).
•
Do not place flammable or combustible materials near the projector!
•
For the F90 projector, the exclusion zone on the lens side within the light beam must be at least 1,5m.
•
For the F70 projector the exclusion zone on the lens side within the light beam must be at least 1,0m.
•
Caution! Hot air is exhausted from the rear vent. Do not place objects that are sensitive to heat nearer than
100 cm (40”) to the exhaust vent.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the
projector and to protect it from overheating, these openings must not be blocked or covered.
•
The openings should never be blocked by placing the projector too close to walls, or other similar surface.
Allow for sufficient distance to walls and ceilings to avoid overheating. Minimum safety distance to the
exhaust area of the unit must not be less than 100 cm (40”) and to the intake area, not less than 50 cm
(20”).
•
This projector should never be placed near or over a radiator or heat register.
•
This projector should not be placed in a built-in installation or enclosure unless proper ventilation is
provided.
•
Do not cover the projector or the lens with any material while the projector is in operation. Keep flammable
and combustible materials away from the projector at all times.
Summary of Contents for F70 Series
