background image

11

ENERGA 80-50

1    INTRODUCTION

1.1    FOREWORD

We would like to congratulate you on your purchase of this modern Barbas built-in wood 
fi re. This quality product will give you years of heating pleasure as you enjoy the play of 
the fl ames and the cosy glow of the fi re. 
The appliance is fi tted with a ceramic particulate fi lter that ensures low emission values 
for the fl ue gases and a very low particulate emission.
This manual contains directions for both positioning the appliance and for its 
environmentally-friendly use. It also contains technical data for the appliance, parts 
information and directions in the event of problems. Study this manual carefully before 
using the stove. We recommend you keep this manual in a safe place for reference 
purposes.

1.2   SAFETY AND INSTALLATION INSTRUCTIONS 

Safety

•  Do not place fl ammable objects within 150 cm of the appliance. Pay special attention  
  to furnishings and ornaments around the fi re.

•  When you use your fi re, the exterior will become hot. Always wear the glove or use  
  the accessories supplied when fi lling etc. Protect yourself and others (especially  

  children!) from burns. Do not leave children unattended when the fi re is burning.

•  Watch your clothing. Synthetic clothing in particular can easily catch fi re and burn  
  intensely.

•  Do not approach the appliance with fl ammable materials or liquids. Any work with  
  solvents, adhesives etc. in the space heated by the fi re can be very dangerous. 

•  Make sure you know what state your chimney is in. Cracks in the chimney may not  
  only lead to damp, staining of walls and leaking of smoke, they can also impair the  
  carrying off of smoke. Make sure you get proper advice from your Barbas dealer or  
  other specialist company.

•  Avoid chimney fi res! 
  Have your chimney swept at least once per year - more often if you use your fi re a  
  lot. Prevent excessive deposits of soot inside the chimney by not burning freshly-cut  
  wood. Instead, burn clean, dry chopped wood.

•  Do not use your built-in fi re as a barbecue. This can cause (fl ammable) fat deposits  
  to be left in the chimney and hastens the chimney becoming clogged. Prevent your  
  chimney being soiled from above (birds’ nests etc.) by fi tting a suitable cap to the  
  chimney pot.

Summary of Contents for ENERGA 80-50













































































Reviews: