![background image](http://html1.mh-extra.com/html/baby-lock/blta/blta_instruction-and-reference-manual_3271077184.webp)
TROUBLESHOOTING
182
■
After Finishing an Operation
Symptom, Cause/solution
Reference
Thread tension is incorrect.
Upper threading is incorrect.
42
Bobbin is set incorrectly.
40
Using improper needle or thread for the selected
fabric.
49
Presser foot holder is not attached correctly.
50
Thread tension is set incorrectly.
62, 139
Bobbin thread is incorrectly wound.
36
Needle is turned, bent or the point is dull.
47
A bobbin designed specifically for this machine is
not being used.
36
Character or decorative stitch patterns are misaligned.
Stitch pattern adjustment settings were set
incorrectly.
97
Stitch pattern does not turn out.
Wrong presser foot.
190
Did not use a stabilizer material on thin fabrics or
stretch fabrics.
70
Thread tension is set incorrectly.
62, 139
Fabric was pulled, pushed or fed at an angle while
it was being sewn.
• Sew while guiding the fabric with your hands so
that the fabric is fed in a straight line.
56
The thread is tangled, for example, in the bobbin
case.
175
The pattern is not embroidered correctly.
Thread is twisted.
—
Thread tension is set incorrectly.
62, 139
Fabric was not inserted into the frame correctly
(fabric was loose, etc.).
123
Stabilizing material was not attached.
• Always use stabilizing material, especially with
stretch fabrics, lightweight fabrics, fabrics with a
coarse weave, or fabrics that often cause
pattern shrinkage. See your authorized Baby
Lock retailer for the proper stabilizer.
122
There was an object placed near the machine, and
the carriage or embroidery frame hit the object
during embroidering.
103
Fabric outside the frame edges interferes with the
arm, so the embroidery unit cannot move.
• Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the arm, and
rotate the pattern 180 degrees.
123
Fabric is too heavy, so the embroidery unit cannot
move freely.
• Place a large thick book or similar object under
the arm head to lightly lift the heavy side and
keep it level.
—
Fabric is hanging off the table.
• If the fabric is hanging off the table during
embroidery, the embroidery unit will not move
freely. Place the fabric so that it does not hang
off the table or hold the fabric to keep it from
dragging.
130
Fabric is snagged or caught on something.
• Stop the machine and place the fabric so that it
does not get caught or snagged.
—
Embroidery frame was removed during
embroidering (for example, to reset the bobbin).
The presser foot was bumped or moved while
removing or attaching the embroidery frame, or the
embroidery unit was moved.
133
Stabilizer is incorrectly attached, for example, it is
smaller than the embroidery frame.
122
Loops appear on the surface of the fabric when
embroidering
The thread tension is incorrectly set.
139
The tension of the upper thread is incorrectly set
for the combination of the fabric, thread and
pattern being used.
• Use the embroidery needle plate cover.
130
The combination of the bobbin case and bobbin
thread is incorrect.
130
Symptom, Cause/solution
Reference
Summary of Contents for BLTA
