Avery Dennison Cutter 2000 Technical Manual Download Page 11

Page: 11 / 17

03/10 Rev. 5.04-01

TECHNICAL MANUAL

Connection, Setup, Service

Cutter 2000

Toothed belt

Tool

Allan key 3 mm

Disassembling/assembly

1. Remove the motor cover and the motor.

For more detailed information, see the
section "Cutter motor".

2. Remove the toothed belt (1). Turn the

oscillator disc (2) somewhat (including the
circular cutter) so that you can guide the
toothed belt past the oscillator disc (fig. 1).

Do not unscrew the screw (3) otherwise

you will have to reset the cutter!

How to? - See in paragraph

Setting the

oscillator disc

on page 12.

Assembly: tension the belt by pushing

sideways against the motor while
tightening the fastening screws.

Photoelectric switch

The photoelectric switch (4) is permanently
connected to the cable tree (fig. 2).

Tool

Allan key 3mm

Disassembling/assembly

1. Remove the motor cover and the motor.

How to? - See in paragraph

Cutter motor

on page 10.

2. Unscrew the Phillips screw (5). Remove

the photoelectric switch.

Summary of Contents for Cutter 2000


















Search results

Summary of Contents for Cutter 2000

Reviews:

Related manuals for Cutter 2000

Brands by name

Popular brands

Avery Dennison Cutter 2000, Technical Manual

Search results

Summary of Contents for Cutter 2000

Reviews:

Related manuals for Cutter 2000

Brands by name

Popular brands