Avaya IP OFFICE 40DHB0002USCL Installation Manual Download | Manualshive

Page: 8 / 70

background image

Page 8 - Regulatory Instructions for Use

Safety and Homologation Statements

Regulatory Instructions for Use

IP Office Operation in Australia

Connection

Connection of IP400 Office products must be via a Line Isolation Unit with a telecommunications

compliance label.

BRI Interface

During the configuration, ensure "000" emergency number is not barred, by performing the following:

Short Code: "000"

Telephone No.: "000;"

Function: "Dial Emergency"

Connections to TS013, the following Bearer Capabilities shall not be used:

7kHz Audio

Video

Restricted Digital Information

If unknown type of number is used in calling party number, the network will use the default CLI.
The system must be configured for Point to Multi point connection to comply with Austel requirements

for connecting to TS013 circuits.
As the IP Office does not support emergency dialing after loss of power, the following warning notice

should be recognized:

WARNING

This equipment will be inoperable when mains power fails.

PRI Interface

During the configuration, ensure "000" emergency number is not barred, by performing the following:

Short Code: "000"

Telephone No.: "000;"

Function: "Dial Emergency"

WARNING

This equipment will be inoperable during mains power failure.

IP Office Operation in Canada

Industry Canada Notification (DoC)

This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.

This is confirmed by the registration number. The abbreviation, IC, before the registration number

signifies that registration was performed based on a Declaration of Conformity indicating that Industry

Canada technical specifications were met.
It does not imply that Industry Canada approved the equipment.
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 1. The REN

assigned to each terminal equipment provides an indication of the maximum number of terminals

allowed to be connected to a telephone interface. The termination on an interface may consist of any

combination of devices subject only to the requirement that the sum of the Ringer Equivalence

Numbers of all the devices does not exceed five.''

Page 8 - Safety and Homologation Statements

IP Office Installation Manual

Regulatory Instructions for Use

40DHB0002USCL – Issue 7 (09/25/2002)

«
...
6
7
8
9
10
...
»

Summary of Contents for IP OFFICE 40DHB0002USCL







































































Reviews:

No comments

Related manuals for IP OFFICE 40DHB0002USCL

Brand: Alcatel Pages: 24

Brand: Azumi Pages: 7

Brand: HTC Pages: 36

Brand: DOPOD Pages: 352

A99-WMTA3030-01

Brand: Westell Pages: 12

DROID INCREDIBLE 4G LTE

Brand: HTC Pages: 2

Brand: Evolveo Pages: 23

Brand: Samsung Pages: 166

Brand: Samsung Pages: 45

Linemex ISDK Series

Brand: Uniphone Pages: 25

Brand: Samsung Pages: 140

Brand: Zte Pages: 48

Brand: Xiaomi Pages: 8

Brand: Xiaomi Pages: 110

Brand: Billow Pages: 131

Brand: Mitel Pages: 29

Brand: Asus Pages: 8

Brand: Asus Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands