Avaya IP OFFICE 40DHB0002USCL Installation Manual Download

Page: 10 / 70

Page 10 - General

IP401 Compact Office Platform

General

The IP401 Compact Office system platform is supplied in two variants:

IP401 Compact Office 2 supports:

Two digital and two analog telephones

A BRI ISDN port (2 trunks)

An four port auto-negotiating 10/100 BaseT LAN hub

IP401 Compact Office 4 supports:

Four digital and four analog telephones

Two BRI ISDN ports (4 trunks)

An eight port auto-negotiating 10/100 BaseT LAN hub.
The auto-negotiating 10/100 BaseT LAN hub provides access to networks and/or up to eight IP

telephones.
The DT ports support Avaya 2000 series telephones. DT ports are set to A-Law PCM encoding at
default but can be programmed to

-Law PCM encoding.

An IP401 Compact Office 2 can be expanded to an IP401 Compact Office 4.
In addition the IP401 Compact Office can be fitted with any of the following optional Integral Modules:

•

WAN Port

This port supports a single synchronous data connection, which can be X.21, V.35 or V.24.

•

Voice Compression Module (VCM)

Supports VoIP applications (over two channels) using Avaya 4600 IP telephone connected via

LAN ports.

•

VME card

Provides memory capacity for embedded voice mail feature.

See page 44 for expansion and page 32 for country specific variants.

Page 10 - IP401 Compact Office Platform

IP Office Installation Manual

General

40DHB0002USCL – Issue 7 (09/25/2002)

Summary of Contents for IP OFFICE 40DHB0002USCL







































































Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands

Avaya IP OFFICE 40DHB0002USCL, Installation Manual

Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands