Avaya IP OFFICE 40DHB0002USCL Installation Manual Download

Page: 23 / 70

IP412 Office Platform

IP412 Office - Front View - Page 23

IP412 Office - Front View

Expansion Ports 1-12

Green Status LEDS

Unit Status LED

Red = Alive but not initiated
Green = Running OK

LAN Ports 1-2

WAN Port

Green Status LED

Trunk Ports 1-8

Green Status LEDS

Port connections

•

LAN Ports

The segmented dual independent auto-negotiating 10/100 BaseT Ethernet ports are used for PC

and server connectivity. They can also be used to connect to the optional IP400 WAN3 Expansion

Module (see page 30) and IP telephones.
Information relating to incoming and outgoing telephone calls can be forwarded to PC based

applications via these ports. These segmented Ethernet ports support separate IP and MAC

addresses and hence a Firewall break may be implemented. They also provide access to the

router functionality/configuration of the IP412 Office platform for both data and Voice over IP

(VoIP) calls. (Where IP telephony is required, a suitable switch, i.e. an Avaya Cajun P130, must

be used.)

Cables

IP412 Office DT PRI 30 E1 & DS PRI 24 T1 are supplied with one red ISDN cable. IP412 Office DT

PRI60 E1 & PRI48 T1 are supplied with two red ISDN cables. For Port Pinouts and Cables, refer to

pages 51 and 55 respectively.

IP Office Installation Manual

IP412 Office Platform - Page 23

40DHB0002USCL – Issue 7 (09/25/2002)

IP412 Office - Front View

Summary of Contents for IP OFFICE 40DHB0002USCL







































































Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands

Avaya IP OFFICE 40DHB0002USCL, Installation Manual

Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands