Avaya IP OFFICE 40DHB0002USCL Installation Manual Download

Page: 67 / 70

Technical Data

Technical Specifications - Page 67

Technical Specifications

General

Dimensions

IP401:

Width:

255mm.

Height:

71mm.

Depth:

235mm.

IP403/6/12 and Expansion Modules : Width: 445mm. Height: 71mm. Depth: 245mm

Environmental

0 to +40

C. 95% relative humidity, non-condensing.

Weight
(in Kgs)

Unit:

401 403 406 412 Analog16 DT/DS16

DT/DS30 WAN3 So8 Phone8 Phone16 Phone30

1.2 2.6 3.0 3.0 2.9

3.0

3.50

2.8 2.75 2.80 2.90 3.10

Power Supply
Consumption
(nominal Watts)

2.5mm DC inlet socket. 24Vdc Power input. Rating 24Vd.c., 2A max.

Unit:

401 403 406 412 Analog16 DT/DS16

DT/DS30 WAN3 So8 Phone8 Phone16 Phone30

24 26 16 17.5 5

12 24 12

Lump-in-Line PSU Power Requirements: I/P 100-240Vac, 50/60Hz, 81-115VA, Input current 2A max

O/P 24Vdc, 1.875A, output Power 45W max.
The Lump-in-line PSU is CE/UL/Dentori Safety Approved.

Interfaces

Interface Information

DTE

25 way D-Type female connector, V.24/V.28. (9 way D-type on IP412s)

ISDN

ROW Interfaces:

BRI :

RJ45 sockets. ETSI S/T Interface to CTR3 for Pan European Connection.

PRI E1:

RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.

PRI E1-R2: RJ45 socket. ETSI T Interface to CTR4 for Pan European Connection.
PRI E1-R2: 75

Ω

BNC Coax.. ETSI T Interface.

PRI T1:

RJ45 socket: FCC Part 68/JATE connection.

USA Interfaces:

PRI T1 Service:

Ground Start (GS) – Default, E&M, 56k data for 5ESS, 56/64/64 restricted for 4ESS

PRI ISDN Switch support:

4ESS, 5ESS, DMS-100, DMS-250 (includes conformance to ANSI T1.607 & Bellcore Special Report
SR4287, 1992

PRI ISDN Services:

AT&T Megacom 800, AT&T WATS (4ESS), AT&T SDS Accunet 56kB/s & 64kB/s (4ESS), AT&T
Multiquest (4ESS).

Analog ports

RJ45 sockets: Loop start/Ground start (regional dependant)

Power Fail ports

RJ45 sockets: telephone ports act as master sockets

ISDN
Data Rates

BRI: B-channel 64kbps or 56kbps, D-channel 16kbps.
PRI: B-channel 64kbps or 56kbps, D-channel 64kbps.

Telephone

RJ45 sockets. EU - Telephone ports act as master sockets.
CLI Schemes: DTMFA, DTMFC, DTMFD, FSK and UK20.
REN = 2
Off Hook current = 25mA.
Ring Voltage = 40V (nominal) RMS.
External Bell (via analog port); REN = 1

LAN

RJ45 sockets. Auto-negotiating 10/100BaseT Ethernet (10Mbps).
Port 8 is MDI/MDIX switchable via the adjacent Cascade

pushbutton switch.

Refer to pages 15, 19 and 23.

WAN

37 way D-Type female sockets. X.21 interface to 2048k bps, V.35 interface to 2048k bps and V.24 Interface to
19k2 bps.

Audio

3.5mm Stereo Jack socket. Input impedance - 10k /channel.
Maximum a.c. signal – 200mV rms.

External
Control

3.5mm Stereo Jack socket. Switching Capacity - 0.7A.
Maximum Voltage - 55V d.c. On state resistance - 0.7

Ω

Short circuit current - 1A. Reverse circuit current capacity - 1.4A.

Installation Manual

Technical Data - Page 67

IP Office

40DHB0002USCL – Issue 7 (09/25/2002)

Summary of Contents for IP OFFICE 40DHB0002USCL







































































Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands

Avaya IP OFFICE 40DHB0002USCL, Installation Manual

Search results

Summary of Contents for IP OFFICE 40DHB0002USCL

Reviews:

Related manuals for IP OFFICE 40DHB0002USCL

Brands by name

Popular brands