AUX ASW-07B4/HSAR Service Manual Download Page 119

Page: 119 / 159

6.2 When the air conditioner is powered on, the outdoor fan, four- way

valve and compressor will start at the same time while when it is

shut down, the outdoor fan and compressor will be shut down at the

same time and so will the four- way valve after 2 minutes' delay.

6.3 Under the mode of heating, the compressor can not be shut down

within 3 minutes after it is powered on unless the operation mode is

changed or the air conditioner is turned off.

6.4 There is a 3 temperature compensating function. The temperature

measured at the in-blow vent minus 3 automatically can be

regarded as that compared with the temperature set (This function

does not exist under other circumstances).

6.5 According to the temperature set, the condition upon which the

compressor will be switched on is indoor temperature

≤

temperature

set-1 While the condition upon which it will be switched off

is indoor temperature is indoor temperature

≥

tempe 1 .

When the indoor temperature is equal to that set, the original

operation mode will be kept.

6.6 Indoor fan control:

6.6.1 Heating operation and prevention of cold wind

When the compressor works:

During the rising process of the temperature of coiled pipe,

the indoor fan will not start if the temperature of the coiled

Summary of Contents for ASW-07B4/HSAR
































































































































































Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands

AUX ASW-07B4/HSAR, Service Manual

Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands