AUX ASW-07B4/HSAR Service Manual Download Page 22

Page: 22 / 159

which lasts more than 2 minutes, the compressor will stop

operating and the indoor fan will go by air quantity set.

10.3.3 When the compressor stops working, it can only be restarted

only if the temperature of indoor coiled pipe rises to more than 7

or the power-off of the compressor lasts more than 6 minutes.

10.4 Protection function of short or open circuit of temperature senor

10.4.1 Powered on, when it is detected that the T ring signal sent by

indoor environment temperature senor is abnormal, the air

conditioner will work under the mode of heating and will not be

powered off if the signal received from remote control is

“heating” or it will work under the mode of refrigeration and will

not be powered off if the signal received from remote control is

“refrigeration” or it will work for 8 minutes and then stop for 3

minutes with the wind speed of “mute cycle dehumidification” if

the signal received from remote control is “dehumidification”.

Besides, the signal of automatic mode sent by remote control

will not be effective, nor will the signal of automatic button

power-on and the related breakdown can be indicated at the

same time.

10.4.2 When it is detected that the T internal coiled pipe signal sent

by indoor coiled pipe temperature sensor is abnormal, the

freezing-proof, cold-wind-proof and overheat-proof functions

Summary of Contents for ASW-07B4/HSAR
































































































































































Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands

AUX ASW-07B4/HSAR, Service Manual

Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands