AUX ASW-07B4/HSAR Service Manual Download Page 128

Page: 128 / 159

will be screened. Under the mode of heating, when the

compressor is powered on, indoor fan will be started after 30

seconds’ delay with the wind speed as set while when

compressor is powered off, indoor fan will be turned off after 30

seconds’ delay and the related breakdown can be indicated at the

same time.

10.4.3 When it is detected that the T external coiled pipe signal sent

by outdoor coiled pipe temperature sensor is abnormal, the air

conditioner will work for 50 minutes, defrost for 10 minutes and

heat in cycles if the signal received from remote control is

“heating” and the related breakdown can be indicated at the

same time while the air conditioner will not be powered off and

will operate normally if the signal received from remote control

is heating or defrosting or ventilation and the related breakdown

can be indicated at the same time.

10.5 disposal of indoor PG electric motor abnormity

When indoor PG electric motor is loaded with voltage, the indoor

fan will operate under the mode of “weak wind” automatically if

the pulse signal feed backed by the indoor electric motor is not

detected within 12 seconds. If the feedback signal detected is

normal, the indoor fan will resume the turning speed set and the

related breakdown indication will be disappear.

Summary of Contents for ASW-07B4/HSAR
































































































































































Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands

AUX ASW-07B4/HSAR, Service Manual

Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands