AUX ASW-07B4/HSAR Service Manual Download Page 67

Page: 67 / 159

When the compressor is shut down, the outdoor fan and indoor fan

will stop working.

When T ring

≥

T set <T ring-1, the compressor will be working for 8 minutes and then

stopping for 3 minutes in cycles.

T set

≥

T ring-1, the compressor will be working for 3 minutes and then

stopping for 6 minutes in cycles.

And when T ring <23

T set

≤

T ring-1, the compressor will be working for 3 minutes and

then stopping for 4 minutes in cycles.

T set >T ring-1, the compressor will be working for 3 minutes and then

stopping for 6 minutes in cycles.

Function of ventilation control

5.1 Under the mode of ventilation, the outdoor fan assembly will

always be shut down.

5.2 The indoor fan will operate as set in the respect of air quantity

without the gear- change of “high power".

5.3 The pendulum leaves will work according to the instructions sent

by remote control.

Heating function

6.1 Under the mode of heating, the temperature range set is between 16

and 32 . And the temperature will be set by remote control.

Summary of Contents for ASW-07B4/HSAR
































































































































































Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands

AUX ASW-07B4/HSAR, Service Manual

Search results

Summary of Contents for ASW-07B4/HSAR

Reviews:

Related manuals for ASW-07B4/HSAR

Brands by name

Popular brands