AT&T TL96276 Complete User'S Manual Download Page 18 | Manualshive

Page: 18 / 180

background image

11

Getting started

Battery installation and charging

Install the battery, as shown below. Once you have installed the battery, the
screen indicates the battery status (see the following table). If necessary, place
the handset in the telephone base or charger to charge the battery. For best
performance, keep the handset in the telephone base or charger when not in
use. The battery is fully charged after 11 hours of continuous charging. See the
table on page 168 for battery operating times.

If the screen is blank or shows

Place in charger

and a flashing , you need

to charge the handset without interruption for at least 30 minutes to give
the handset enough charge to use the telephone for a short time. When the
battery is low, the handset shows

Low battery

and a flashing . If you are on a

call in low battery mode, the handset beeps every minute.

The following table summarizes the battery charge indicators and actions
to take.

Battery indicators

Battery status

Action

The screen is blank or
shows

Place in charger

and flashes.

The battery has no or very
little charge. The handset
cannot be used.

Charge without interruption (at least
30 minutes).

The screen shows

Low battery

and

flashes.

Battery has enough
charge to be used for a
short time.

Charge without interruption (at least
30 minutes).

The screen shows

HANDSET X

.

Battery is charged.

To keep the battery charged, place it in
the telephone base or charger when not
in use.

Plug the battery connector securely into the socket inside the handset
battery compartment. Insert the supplied battery with the label

THIS SIDE UP

facing up, as indicated.

1.

THIS SIDE UP / CE

CÔ

TÉ

VERS LE HA

UT

«
...
16
17
18
19
20
...
»

Summary of Contents for TL96276





















































































































































































Reviews:

No comments

Related manuals for TL96276

Brand: NEC Pages: 10

Brand: NEC Pages: 27

Brand: Panasonic Pages: 8

KXTGA820 - EXPND DIGITAL CORDLESS HANDSET

Brand: Panasonic Pages: 5

Brand: Fanstel Pages: 22

FREELANCE XC 1500

Brand: BT Pages: 2

Brand: GE Pages: 14

Brand: Depaepe Telecom Pages: 15

Brand: AT&T Pages: 21

Brand: Uniden Pages: 40

Brand: VanAccess Pages: 24

Hydro-Force 62195

Brand: Bestway Pages: 6

Brand: Aastra Pages: 100

Brand: Angekis Pages: 4

Brand: Easydive Pages: 2

Brand: BRONDI Pages: 14

Brand: LG Pages: 75

Brand: LG Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands