ASTRO ATS-8900 Operator'S Manual Download Page 9

Page: 9 / 48

ASSEMBLY AND INSTALLATION

SECTION 2 -

Assembly and Installation

The ATS-8900 is shipped in a single carton.

Assembly

Choose a Location

Place the Tabber with its Feeder on a sturdy worktable or cabinet at least 12 inches from any
walls. Allow enough room to place the Feeder on the same work surface. Protect the Tabber
from excessive heat, dust, and moisture

–

avoid placing it in direct sunlight.

CAUTION

THE UNIT IS HEAVY.

IT IS STRONGLY RECOMMENDED THAT TWO TECHNICIANS REMOVE THE

TABBER FROM THE CARTON AND PLACE IT ON THE WORKING SURFACE.

Installing the Reel Assembly

Place the Reel Assembly over the Guide
Pin

[1]

. Make sure that the Head is over

Guide Pin

[2]

while you are tightening the

Tab Positioning Knob

[3]

clockwise.

NOTE:

Make sure the plastic bushings

[4]

, located at the front and back of the

hole for Guide Pin

[1]

, are installed.

Summary of Contents for ATS-8900
















































Search results

Summary of Contents for ATS-8900

Reviews:

Related manuals for ATS-8900

Brands by name

Popular brands

ASTRO ATS-8900, Operator'S Manual

Search results

Summary of Contents for ATS-8900

Reviews:

Related manuals for ATS-8900

Brands by name

Popular brands