Associated 12-1015 rev-B User Manual Download Page 43 | Manualshive

Page: 43 / 50

background image

___________________________________________________________________________________

‐

43

‐

12‐1015 rev‐B

User’s Manual Version 14.12

10.0 PC Link

12-1015 REV-B is also designed to link with PC for data storage and printout
through PC printer. To do so, the PC has to install the driver and the software
provided in order to operate.

10.1 Installing Driver.

Important Note:
Before you start to install the driver, please do not plug 12-1015 REV-B into the
computer’s USB port or else the installation will fail and the computer cannot detect
the proper driver for 12-1015 REV-B when connected.

If you have made the above error and wish to install the driver the second time,
you need to uninstall the previously installed driver first before starting to reinstall
again. This time make sure that 12-1015 REV-B is not plugged in.

Step 1.

You can install the driver from the CD provided:

First click to open the folder:

You will find the following files:

Step 2.

Double click on the icon

. .The installation will start automatically.

Typical example below is for Windows 7 operating system.

«
...
41
42
43
44
45
...
»

Summary of Contents for 12-1015 rev-B



















































Reviews:

No comments

Related manuals for 12-1015 rev-B

Brand: Jennov Pages: 50

Brand: Campbell Pages: 362

Brand: Campbell Pages: 60

Brand: Campbell Pages: 116

Brand: Campbell Pages: 30

Brand: Campbell Pages: 55

Brand: Keithley Pages: 201

Brand: PAT Pages: 57

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: A&D Pages: 39

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 110

Portatone PSR-5700

Brand: Yamaha Pages: 79

Brand: Yamaha Pages: 112

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands