Associated 12-1015 rev-B User Manual Download Page 25 | Manualshive

Page: 25 / 50

background image

___________________________________________________________________________________

‐

25

‐

12‐1015 rev‐B

User’s Manual Version 14.12

6.

LIFE:

91 %

(Health)

This is an indication of the battery life (State of Health) in percentage. If the life
falls below 46%, the RESULT will display “Replace” and it is time to change to a
new battery.

Explanation of the following terms used as shown on the LCD display:



CCA (Cold Cranking Amps) – most commonly used Standard.

CCA is a rating used in the battery industry to rate a battery’s ability to start
an engine in cold temperatures. This rating is the number of amperes that a
new fully charged battery can delivery at 0



F (-18



C) for 30 seconds, while

maintaining a voltage of at least 7.2 Volts for a 12V battery during cranking.



SAE (The Society of Automotive Engineers) Standard.

SAE has established Cold Cranking Amperes (CCA) rating for batteries as
their standard. Therefore this rating is the same as CCA rating as
mentioned above.



IEC (International Electro technical Commission) Standard.

IEC amperes rating require that at 0



F (-18



C), the number of amperes that

the 12V battery can deliver while maintaining a voltage of at least of 8.4
Volts for 60 seconds during cranking.



EN (European Norms) Standard.

EN amperes rating require that at 0



F (-18



C), the number of ampere that

the 12V battery can deliver while maintaining a voltage of at least 6.0 Volts
for 180 seconds during cranking.



JIS# (Japanese Industrial Standard)

JIS # amperes’ rating is based on Ampere Hours and is calculated using 20
hours rating. In this manual, it is using CCA ratings reference table list
provided basing on the JIS model number (See page 29 & 30).



DIN (Deutsches Industrie Normen)

Standard.

Basing on DIN , the rating requires that at 0



F (-18



C), the 12V battery is able

to deliver the number of amperes while maintaining a voltage of at least of 9.0
Volts for 30 seconds and 8.0 Volts for 150 seconds during cranking.



CA (Cranking Amperes) Rating.

This rating is the number of amperes that a new fully charged battery can
delivery at 32



F (0



C) for 30 seconds, while maintaining a voltage of at least

7.2 Volts for a 12V battery during cranking.



Unknown

If you are not sure which ratings (CCA, EN, IEC, JIS or DIN) that the battery is
based on, then choose this setting. It will show the battery’s Voltage (State of
Charge), CCA and the Internal Resistance (m Ohm) only. This selection can
also be used to test 12V - Deep Cycle Batteries.

«
...
23
24
25
26
27
...
»

Summary of Contents for 12-1015 rev-B



















































Reviews:

No comments

Related manuals for 12-1015 rev-B

Brand: ABB Pages: 20

Brand: Utilitech Pages: 2

Brand: i-SENS Pages: 50

Brand: Vega Pages: 28

Brand: Vega Pages: 20

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Flytec Pages: 2

Brand: Schneeberger Pages: 35

Brand: SIGLENT Pages: 32

DT4120 PS Series

Brand: Datcon Pages: 92

Brand: SANKO Pages: 97

Brand: Staco Energy Pages: 2

Brand: Water I.D. Pages: 56

Brand: Meec tools Pages: 23

NetSure M832DNA

Brand: Vertiv Pages: 176

FlowStar2 LB 514

Brand: BERTHOLD TECHNOLOGIES Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands