ashtech Reliance FS/2 Operation Manual Download Page 104

Page: 104 / 186

Reliance with FS/2 Field Operations Manual

Table 4.14 describes the FEATURE OFFSET screen fields.

Table 4.15: Offset Screen Field Descriptions

Field

Description

MAGNETIC/TRUE

For point offsets only. True or magnetic azimuth. If using a LRF, make
sure the LRF and FAMlog are both set to the same system.

AZIMUTH

For point offsets only. Offset azimuth.

SLOPE DISTANCE

Offset distance along the slope.

INCLINATION

Angle between a horizontal and the offset point or line. If the offset is
approximately level, use 0.00.

DIRECTION

For line/area offsets only. Offset direction relative to path of travel.
Toggle LEFT or RIGHT.

UPDT

Accept current parameters.

CONN

Establish connection with LRF. Available only if connection to the LRF
has not been established.

DCON

Close communication with LRF. Available only if connected to a LRF.

LCOM

Opens the LRF COMMUNICATION PARAMETERS screen.

RETN

Returns to the FEATURE ATTRIBUTE screen. Values manually
entered on this screen accepted only if F1 (UPDT) was pressed.

Summary of Contents for Reliance FS/2



























































































































































































Search results

Summary of Contents for Reliance FS/2

Reviews:

Related manuals for Reliance FS/2

Brands by name

Popular brands

ashtech Reliance FS/2, Operation Manual

Search results

Summary of Contents for Reliance FS/2

Reviews:

Related manuals for Reliance FS/2

Brands by name

Popular brands