![artisan TRACKPOINT 3 4211A Operation And Maintenance Manual Download Page 113](http://html.mh-extra.com/html/artisan/trackpoint-3-4211a/trackpoint-3-4211a_operation-and-maintenance-manual_2978406113.webp)
TRACKPOINT 3
OPERATION
3-50
USBL Get TrackPoint Config
This synchronizes the Trackman/PC with the parameters from the TrackPoint Signal Interface Mod-
ule. (Takes a while!)
C A U T I O N
Do not use this unless you are swapping out topside processors and you want to maintain previous
setup. No parameters are saved in the TrackPoint II Deck Unit when power is turned off. The unit
starts up in a default mode when power is applied each time.
USBL Send TrackPoint Config
Synchronizes the TrackPoint SP/IM using the Trackman saved parameters.
USBL Get Sensor Data
Queries the Deck Unit to read the analog sensor inputs and display their values. The A/D data is
read once per command. It is possible to repeat the command while leaving the box on the screen.
Heading Time:
The time the heading was received from the RS232 port.
Heading:
The Heading value as received.
Heading ID:
The heading reference, either Magnetic or True.
A/D Time:
The time that the A/D read the values as shown. The A/D reads all sensor
data within 0.2ms.
Pitch/Roll:
The analog pitch value in degrees.
Compass:
The analog compass in degrees.
Depth 1:
The analog depth value in meters.
Depth 2:
The analog depth value in meters.
Temperature: The temperature of the Hydrophone in degrees C.
Summary of Contents for TRACKPOINT 3 4211A
