Arcom ZyWAN User Manual Download | Manualshive

Page: 108 / 114

background image

ZyWAN User Manual

Appendix A – Contacting Arcom

© 2008 Arcom Issue D

108

Appendix A – Contacting Arcom

Arcom sales

Arcom’s sales team is always available to assist you in choosing the board that best
meets your requirements.

Arcom
7500W 161

st

Street

Overland Park
Kansas
66085
USA

Tel:

913 549 1000

Fax:

913 549 1002

E-mail:

[email protected]

Comprehensive information about our products is also available at our web site:

www.arcom.com

and

www.zywan.com

.

While Arcom’s sales team can assist you in making your decision, the final
choice of boards or systems is solely and wholly the responsibility of the buyer.
Arcom’s entire liability in respect of the boards or systems is as set out in
Arcom’s standard terms and conditions of sale. If you intend to write your own
low level software, you can start with the source code on the disk supplied.
This is example code only to illustrate use on Arcom’s products. It has not been
commercially tested. No warranty is made in respect of this code and Arcom
shall incur no liability whatsoever or howsoever arising from any use made of the
code.

Arcom technical support

Arcom has a team of dedicated technical support engineers available to provide a quick
response to your technical queries.

Tel:

913 549 1010

Fax:

913 549 1001

E-mail:

[email protected]

Eurotech Group

Arcom is a subsidiary of Eurotech Group. For further details, see

www.eurotech.com

«
...
106
107
108
109
110
...
»

Summary of Contents for ZyWAN



















































































































Reviews:

No comments

Related manuals for ZyWAN

Brand: Ultratec Pages: 32

Brand: P1 Pages: 5

Brand: P1 Pages: 17

Brand: P1 Pages: 2

Brand: RACOM Pages: 56

Brand: Virgin Pages: 44

Brand: Zoom Pages: 68

RB IndustrialRT

Brand: Teleorigin Pages: 13

Brand: MikroTik Pages: 9

Brand: Wireless Matrix Pages: 31

Brand: goTenna Pages: 22

Brand: Tahoe Pages: 36

FRITZ!WLAN USB Stick

Brand: Fritz! Pages: 51

Brand: O2 Pages: 8

Brand: O2 Pages: 12

Brand: FRITZ!WLAN Pages: 6

Brand: FRITZ!WLAN Pages: 6

Brand: Paradise Datacom Pages: 215

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands