Applied Membranes W-G1054EM Operation And Maintenance Manual Download Page 37

Page: 37 / 40

Installation and Service Manual – Metered Carbon Filter

Page 37

Troubleshooting

PROBLEM

POSSIBLE CAUSE

SOLUTION

Inlet pressure low

Low supply pressure

Correct incoming supply pressure

Low flow from source

Remove blockage or other restrictions

Treated water flow low

Media/Resin bed fouled

Backwash Filter

Valves closed

Check valves and fully open

Treated water has chlorine

Bypass valve is open or faulty

Fully close bypass valve or replace

Damaged seal/stack assembly

Replace seal/stack assembly

Control valve body type and
piston type mismatched

Verify proper control valve body type and piston
type match

Fouled media bed

Replace media bed

No Display on PC Board

No Power at electrical outlet

Repair outlet or use working outlet

Control Valve Power Adapter
not plugged into outlet or power
cord end not connected to PC
board connection

Plug Power Adapter into outlet or connect power
cord end to PC Board connection

Improper Power Supply

Verify power voltage is being delivered to the PC
Board

Defective Power Adapter

Replace Power Adapter

Defective PC Board

Replace PC Board

PC Board does not display
correct time of day

Power Adapter plugged into
electric outlet controlled by light
switch

Use uninterrupted outlet

Tripped breaker switch and/or
tripped GFI

Reset breaker switch and/ or GFI switch

Power outage

Reset time of day. If PC Board has battery backup
present the battery may be depleted. See Front
Cover and Drive Assembly drawing for
instructions.

Defective PC Board

Replace PC Board

Display does not indicate that
water is flowing.

Bypass valve in bypass position

Turn bypass handles to place bypass in service
position

Meter is not connected to meter
connection on PC Board

Connect meter to three pin connection labeled
METER on PC Board

Restricted/ stalled meter turbine

Remove meter and check for rotation or foreign
material

Meter wire not installed securely
into three pin connector

Verify meter cable wires are installed securely into
three pin connector labeled METER

Defective meter

Replace Meter

Defective PC Board

Replace PC Board

Summary of Contents for W-G1054EM







































Search results

Summary of Contents for W-G1054EM

Reviews:

Related manuals for W-G1054EM

Brands by name

Popular brands

Applied Membranes W-G1054EM, Operation And Maintenance Manual

Search results

Summary of Contents for W-G1054EM

Reviews:

Related manuals for W-G1054EM

Brands by name

Popular brands