Applied Membranes W-G1054EM Operation And Maintenance Manual Download Page 20

Page: 20 / 40

Installation and Service Manual – Metered Carbon Filter

Page 20

Valve History

For all steps below: Press the NEXT button to proceed to the next step. Press REGEN to return to previous step or exit.

STEP 1VH

Press

▲

and

▼

simultaneously for three seconds and release. Then press

▲

and

▼

simultaneously and release. If screen in step 2VH does not appear in 5 seconds the
lock on the valve is activated. To unlock press

▼

, NEXT,

▲

, and SET CLOCK in

sequence, then press

▲

and

▼

simultaneously for 3 seconds and release. Then press

▲

and

▼

simultaneously and release.

STEP 2VH

Software Version: This display shows the software version of the valve. Press the
NEXT button to go to Step 3VH. Press REGEN to exit Valve History.

STEP 3VH

Flow rate, maximum since startup: This display shows the maximum flow rate in
gallons per minute that has occurred since startup.

STEP 4VH

Gallons, total used since start-up: This display shows the total gallons treated since
startup.

STEP 5VH

Days, total since start-up: This display shows the total days since startup.

STEP 6VH

Regenerations, total number since start-up: This display shows the total number of
regenerations that have occurred since startup.

STEP 7VH

Error Log: This display shows a history of the last 10 errors generated by the control
during operation. Press the

▲

▼

buttons to review each error recorded. Press the

NEXT button to exit Valve History.

Note: Values in steps 3VH through
7VH cannot be reset.

Summary of Contents for W-G1054EM







































Search results

Summary of Contents for W-G1054EM

Reviews:

Related manuals for W-G1054EM

Brands by name

Popular brands

Applied Membranes W-G1054EM, Operation And Maintenance Manual

Search results

Summary of Contents for W-G1054EM

Reviews:

Related manuals for W-G1054EM

Brands by name

Popular brands