ANTAIRA STE-501C User Manual Download Page 3 | Manualshive

Page: 3 / 51

background image

User’s Manual Version 1.

4

Serial to Ethernet Device Server
STE-501C

Copyright © 201

7

Antaira Technologies, LLC

All rights reserved.

2

This document is intended to provide customers with brief descriptions on the product and to assist customers
to get started. For detail information and operations of the product, please refer to the manual in the CD
attached.

FCC

W

ARNING

Class A for

Ethernet Serial Server

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and radiates
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expenses.

A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to
the nearby radio and television reception. It is essential that only the supplied power cord can be used.

Use only shielded cables to connect the device’s RS-232 or RS-485 port.

Be cautioned that changes or modifications not explicitly approved by Antaira Technologies could void your
authority to operate the equipment.

«
1
2
3
4
5
...
»

Summary of Contents for STE-501C




















































Reviews:

No comments

Related manuals for STE-501C

Brand: IBM Pages: 40

Brand: Panasonic Pages: 16

SuperServer 6041G

Brand: Supero Pages: 114

Brand: QNAP Pages: 203

Brand: QNAP Pages: 53

Brand: San Telequip Pages: 49

SafeNet ProtectServer PCIe HSM 5.4

Brand: Thales Pages: 27

Brand: Medion Pages: 112

DIRECTORY SERVER 8.0

Brand: Red Hat Pages: 128

Brand: Axis Pages: 172

SuperStorageSystem SSG-2028R-DN2R40L

Brand: Supermicro Pages: 84

InfiniteStorage 3000

Brand: Silicon Graphics Pages: 50

Brand: Inventec Pages: 258

Brand: Paxar Pages: 294

Brand: Deep Secure Pages: 12

Brand: Inspur Pages: 276

Brand: UTEK Pages: 21

Brand: Gateway Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands