ANTAIRA STE-501C User Manual Download Page 51

Page: 51 / 51

User’s Manual Version 1.

Serial to Ethernet Device Server
STE-501C

Antaira Technologies, LLC

Broadcast IP

Except for the default IP 255.255.255.255, other items (IPs) are read from the
file “seg.cfg”. This field specifies a detecting IP range. It may be a designated IP
or a broadcast IP.

Wishes

Specifies minimum number of the devices one wish to get reply from after
sending an

Invite

request. If there is not as many as devices responding to

oner invitation, the system repeatedly sends invitation until oner request is
fulfilled.

Reply

Indicates the actual number of devices this utility program detected.

Retry

Specify the number of times that an Invite request is re-sent.

Locate

Locate the specified device.

Reset

Reset the selected device.

Config

Configure the selected device.

Exit

Exit this utility.

IP Address

Indicate the IP address of the device that replied to ones request.



Leading tag “!” stands for IP address collision, possibly caused by

duplicated IP addresses on the network.



Leading tag “?” stands for Mac address collision, possibly caused by

duplicated Mac addresses on the network.

MAC Address

Indicates the MAC address of responding device.

Gateway

Indicates the IP address of the gateway.

Subnet Mask

Indicates the TCP/IP network mask.

Indicates the OS version of the responding device.

AP Version

Indicates the AP version of the responding device.

Model

Indicates the model number of the responding device. This field is only
available for monitor.exe version 2.0 and above.

Summary of Contents for STE-501C



















































Search results

Summary of Contents for STE-501C

Reviews:

Related manuals for STE-501C

Brands by name

Popular brands

ANTAIRA STE-501C, User Manual

Search results

Summary of Contents for STE-501C

Reviews:

Related manuals for STE-501C

Brands by name

Popular brands