Ankom TDF Operator'S Manual Download Page 78

Page: 78 / 78

Automation

saves

time

and

money!

ANKOM

Technology

international

company

with

products

that

include…

A2000

Fiber

Analyzer



Crude Fiber (AOCS Ba 6a-05), ADF, NDF



Automatically adds solutions and rinses



Batch process - up to 24 samples at one time

XT15

Fat

Extractor



Official Method AOCS Am 5-04



Fully automatic



Solvent recovery at 97% or greater



Batch process - up to 15 samples at one time

Gas

Production

System



High sensitivity pressure measurement



Applications include: Biomass-to-Energy analysis (e.g., Ethanol, methane, etc.),
Biodegradability, Ruminant Nutrition, Yeast Activity, Beer/Wine Fermentation,
Soil respiration, BOD, Human Digestion, etc.



Wireless Computer control and data storage

Chemicals



A wide variety of chemicals used for many different lab operations



Pre-mixed solutions available

Please

visit

our

web

site

www.ankom.com

for

more

information.

2052

O’Neil

Rd,

Macedon

14502

Telephone:

(315)

986

‐

8090

Fax:

(315)

986

‐

8091

www.ankom.com

Summary of Contents for TDF















































































Search results

Summary of Contents for TDF

Reviews:

Brands by name

Popular brands

Ankom TDF, Operator'S Manual

Search results

Summary of Contents for TDF

Reviews:

Brands by name

Popular brands