manualshive.com logo in svg

Ankom TDF, Operator'S Manual

Share
Download
Ankom TDF Operator'S Manual Download Page 54

Operator’s

 

Manual

 

 

 

 

 

 

 

pg.

 

54

 

 

Rev

 

A

 

4/30/12

 

 

6.

 

Top

 

process

 

–

 

ABORT

 

When pressed, button #6 aborts the process currently running in the top section of the instrument. 

 

This button is only displayed when an ABORT operation is allowed. 

 

7.

 

Bottom

 

process

 

–

 

Name

 

Box #7 always displays “SDF” to represent an SDF process within an IDF/SDF procedure or the precipitation process 
within a TDF procedure. 

8.

 

Bottom

 

process

 

–

 

Progress

 

Box #8 displays the actual time remaining for the bottom process. 

9.

 

Bottom

 

process

 

–

 

Action

 

Box #9 displays different detailed actions as they occur during the process that is currently running in the bottom section 
of the instrument. 

10.

 

Bottom

 

process

 

–

 

ABORT

 

When pressed, button #10 aborts the process currently running in the bottom section of the instrument. 

 

This button is only displayed when an ABORT operation is allowed. 

 

11.

 

FAULT

 

Button #11 is displayed if a fault occurs within the instrument. When button #11 is pressed, the Fault Screen is displayed. 
This screen has information about all faults that have not been cleared. See the Fault Handling section of this manual for 
more information. 

12.

 

Display

 

Temperatures

 

When button #12 is pressed, temperatures of the In-line Heater and all six Heating Paddles are displayed.  

 

The readings dynamically change as the temperature changes. 

13.

 

Start

 

new

 

procedures

 

Button #13 is displayed when a top process completes. At that time, the button reads: “Start New Procedure?” Button #13 
is also displayed when a bottom process completes and no top process is in progress. At that time, the button reads: “Main 
Menu.” When button #13 is pressed, the appropriate screen for starting a new procedure is displayed. 

 

Temperature

 

Monitor

 

(°C)

 

← 

XX

 

Paddle

 

1

 

XX

 

Paddle

 

2

 

XX

Paddle

 

3

 

XX

Paddle

 

4

 

XX

Paddle

 

5

 

XX

 

Paddle

 

6

 

XX

 

In

‐

line

 

Heater

 

Summary of Contents for TDF















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands