manualshive.com logo in svg

Ankom TDF, Operator'S Manual

Share
Download
Ankom TDF Operator'S Manual Download Page 25

 

Operator’s

 

Manual

 

 

 

 

 

 

 

 

 

Rev

 

A

 

4/30/12

  

   

pg.

 

25

 

 

 

 

11.11

 

If you plan to check the pH during the AMG step in the IDF process, press the Yes button. Otherwise, press the 
No button. The following screen will be displayed. 

 

 

11.12

 

The instrument is now completely set up and ready to automatically run the IDF/SDF procedure. Press the 
START button to begin. At the beginning of each new run, the instrument automatically runs a test to check for
leaks in the tubing. 

 

For the first run after a power-up cycle, or for the first run after the instrument has sat idle for twelve hours, the 
following status screen will be displayed.

 

 

If the fluid lines are already charged properly, or when the line charge is complete, the following status screen will 
be displayed. 

 

Status

 

 

Overall

 

Progress

 

Action

 

in

 

progress

 

IDF

 

Time

 

remaining:

 

Lines

 

Charging

 

Please

 

wait…………..

 

XX:XX:XX

 

SDF

 

Time

 

remaining:

 

 

XX:XX:XX

 

 

 

pH

 

required?

  

Display

 

Temperatures

 

Yes

 

AOAC

 

991.43

 

IDF/SDF

 

 

Press

 

START

 

to

 

begin

 

AOAC

 

991.43

 

IDF/SDF

 

← 

START

 

Check

 

pH

 

manually?

 

AOAC

 

991.43

 

IDF/SDF

 

← 

Yes

No

Summary of Contents for TDF















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands