Angelo Po FX101 G 2, Installation And Operation Manual

Page: 29 / 132

Combination Oven Installation and Operation Manual
29
Section 5
Operation
‡ 6KRZV WKH IXQFWLRQ VHW LQ 6WHDP FRRNLQJ
PRGH RQO\ LI &,%86 3/86 RU &,%86
3/86IXQFWLRQKDVEHHQVHW
10. “Product core probe” or “vacuum”
temperature setting button:
‡ 7R VHW WKH FRRNLQJ WHPSHUDWXUH LQVLGH
the product measured by the core probe
RSWLRQDO RQ OHYHO VWDQGDUG RQ OHYHO
RUZLWKYDFXXPRSWLRQDOSUHVVRQFHWKH
LFRQ ÀDVKHV WR VHW WKH WHPSHUDWXUH XVLQJ
knob (21) .
‡ 0RGL¿HVWKHWHPSHUDWXUHLQVLGHWKHSURGXFW
during cooking: press once to show the
temperature value on display
(8) .
Press the button and turn knob (21) to
modify the value set.
11. Burner icon:
ZKHQOLWLQGLFDWHVEXUQHULVRQ
12. Reset button: resets alarms (beepers and
OLJKWV
13. “ECO” button: used to activate or deactivate
the energy saving function (to be used for
UHGXFHGORDGVRQO\
‡ 3UHVVRQFHLFRQLVOLWZLWKDJUHHQOLJKWWR
WXUQWKH³(&2´IXQFWLRQRQ
14. Fan speed button: used to set three speeds of
the fan wheel.
‡
max continuos speed : when icon switched
Off.
‡
intermittent speed : press once the button
DQGWKHLFRQVZLWFKHV2QZKLOHWKHGLVSOD\
(9)
ZLOOVKRZDEOLQNLQJLQWHUPLWWHQWOHG
‡
min continuous speed : press twice the
button and the icon switches On.
15. Optional probe icon: when switched “ON”
indicates the vacuum probe has been inserted.
This function excludes the use of the main probe
at the core of the oven”.
‡ 3UHVV EXWWRQ
(10) to set the vacuum probe
temperature using knob (21) .
In “Convection cooking” mode you can adjust
the percentage of opening of the vent, which
is shown on the display (9) (“0” = vent always
open; “100” = vent always closed).
³67$576723´ EXWWRQ
Starts or ends the
selected program cycle shown on the display
FRRNLQJF\FOHZDVKLQJF\FOHHWF
1 2 3
7
4
5
6
12
13
16
17
18
21
8
9
10
11
15
14
20
19
22
‡ ,FRQOLWJUHHQOLJKWSURJUDPF\FOH¿QLVKHG
‡ ,FRQOLWUHGOLJKWSURJUDPF\FOHUXQQLQJ
17. Steam injection button: increases humidity.
3UHVV WKH EXWWRQ WR LQMHFW VWHDP IRU VHFRQGV
into the oven during any cooking phase.
18. “Recall” program button:
‡ 7KH EXWWRQ VHOHFWV WKH SUHVHW VWDQGDUG
regeneration programs.
‡ 3UHVVWKHEXWWRQRQFHDQGGLVSOD\
(7) will
show the message “P01”.
‡ 3UHVVWKHEXWWRQWZLFHDQGGLVSOD\
(7) will
show the message “P02”.
‡ 3UHVV WKH EXWWRQ WLPHV DQG GLVSOD\
(7)
will show the message “P03”.