manualshive.com logo in svg

Ametek OCS 500 M6, Manual For Operation, Page: 55 / 80

Share
Download
Ametek OCS 500 M6 Manual For Operation Download Page 55

AMETEK CTS 

 

OCS 500 N6 series 

Manual for Operation 

V 5.24 

55 / 80 

8.1.3. 

User Test Routines  

The user can program, save and recall his own specific test routines. The next pages show the selection of the 
functions. 

Ringwave 

IEC 61000-4-12 

F1 :  Change polarity after n pulses 
F2 :  Voltage change after n pulses by 

V 

F3 :  Change Angle after n pulses by 

a 

F4 :  Change coupling after n pulses 
 
 
 

F1 

F2 

F3 

F4 

F5 

F6 

F7 

After selection the last used test parameters will be indicated on the display.  

Customized test routines  

The software controls user test routines according to the specification of the user. All limitations are the same as 
defined under Quick Start.  

 

F1 Change polarity after n pulses 

After the release of the preselected number of pulses the 
polarity is changed. The procedure always starts with 
positive polarity and changes than to negative. The same 
parameters as under Quick Start can be selected. 

 

 

F2 Voltage change after n pulses by 

V 

The test voltage V is changed from V1 to V2. After the preselected 
number pulses the test level is changed by 

V until V2 is reached. 

The same parameters as under Quick Start are selectable. 
For the limitation of the max. Admissible repetition rate the 
higher value of V1 and V2 is valid.  

 

 

F3 Change the phase angle after n pulses by 

A 

The phase angle related to which the surge pulse is 
released is changed from A1 to A2. After the preselected 
number of n pulses the actual phase angle is changed by 

A 

until A2 is reached. The same parameters as under Quick 
Start can be selected. 

 

 

F4 Change coupling after n pulses 

The coupling mode will automatically be changed after the 
preselected number of pulses has been released. All 
possible coupling modes will be selected. The same 
parameters as under Quick Start can be selected. 

 

 

Summary of Contents for OCS 500 M6

















































































Reviews:

No comments