manualshive.com logo in svg

Ametek OCS 500 M6, Manual For Operation, Page: 23 / 80

Share
Download
Ametek OCS 500 M6 Manual For Operation Download Page 23

AMETEK CTS 

 

OCS 500 N6 series 

Manual for Operation 

V 5.24 

23 / 80 

3.7. 

Setup  

 

Page 3 

SETUP 
F1 : Change language  
F2 : LCD - Backlighting  
F3 : Interfaces  
F4 : Beeper 
F5 : Power 

– on counter  

 
 

F1 

F2 

F3 

F4 

F5 

F6 

F7 

F1 Change language 

The user can chose between two languages, German and English. The user can chose between two languages, 
German and English. 

F2 LCD - Backlighting 

With the use of F2 the backlighting can be switched on or off.  
Additionally the 

Auto Off

 function can be programmed to switch Off the backlighting after a defined time that the 

equipment has not been in operation (1 - 30minBecause of the limited lifetime of LCD displays, approx. 10,000h 
this function should always be activated. 

F3 Interfaces  

This menu will help the user to define the status of the integrated serial and parallel interfaces, e.g. the baud rate 
of the RS 232 or the address of the IEEE interface. 

F4 Beeper 

In the beep menu F1 is the selector for switch ON / OFF the keyboard-beep. The test-finish-beep is not 
selectable and sounds always 3 times when a test routine is finished. 

F5 Operating time  

Pressing of F5 will show the total operating time of the test equipment. There are two timers,  
- Total operating time (powered on) 
- Testing time (total testing time) 

Summary of Contents for OCS 500 M6

















































































Reviews:

No comments