Ametek OCS 500 M6 Manual For Operation Download Page 21

Page: 21 / 80

AMETEK CTS

OCS 500 N6 series

Manual for Operation

V 5.24

21 / 80

3.6.

Service

SERVICE
F1 : Addresses
F2 : Setup
F3 : Change standard levels

F7 : Status

F1 Addresses

The addresses of the AMETEK CTS GmbH in
Switzerland and Germany are shown. The addresses
of all AMETEK CTS sales agencies are listed on the
web site of EM TEST under :

www.emtest.com

F2 Set-up

The software will clearly explain the set-up procedure.

F3 Change standard levels OCS 500 N6.x

The stored standard test levels can be changed within this menu.

F1: Reset all standard levels

F2: Change standard level for IEC 61000-4-18

Damped Oscillatory 100 kHz

F3: Change standard level for IEC 61000-4-18

Damped Oscillatory 1MHz

F4: Change standard level for IEC 61000-4-12

Ringwave 100 kHz

F5: Change standard level for IEC 61000-4-10

100 kHz Damped Oscillatory Magnetic Field

F6: Change standard level for IEC 61000-4-10

1 MHz Damped Oscillatory Magnetic Field

F7: Change standard level for IEC 60255-26

Damped Oscillatory 1MHz ext.

F3 Change standard levels OCS 500 N6F.x

The stored standard test levels can be changed within this menu.

F1 Fast Damped Osc.

IEC 61000-4-18

F1: Set all standard acc. to standard

F2: Damped Osc. 3MHz

IEC 61000-4-18

Damped Oscillatory 3MHz

F3: Damped Osc. 10MHz

IEC 61000-4-18

Damped Oscillatory 10MHz

F4: Damped Osc. 30MHz

IEC 61000-4-18

Damped Oscillatory 30MHz

F2 Slow Damped Osc.

IEC 61000-4-18

F1: Set all standard acc. to standard

F2: Damped Osc 100 kHz

IEC 61000-4-18

Damped Oscillatory 100 kHz

F3: Damped Osc 1MHz

IEC 61000-4-18

Damped Oscillatory 1MHz

F4: Damped Osc 100kHz MF IEC 61000-4-18

Damped Oscillatory 100 kHz H-Field

F5: Damped Osc 1MHz MF

IEC 61000-4-18

Damped Oscillatory 1MHz H-Field

F3 Ringwave Gen. 100kHz

IEC 61000-4-12

F1: Set all standard acc. to standard

F2: Ringwave Gen. 100kHz

IEC 61000-4-12

Ringwave 100kHz

Summary of Contents for OCS 500 M6

















































































Search results

Summary of Contents for OCS 500 M6

Reviews:

Ametek OCS 500 M6, Manual For Operation, Page: 21 / 80

Search results

Summary of Contents for OCS 500 M6

Reviews: