manualshive.com logo in svg

AMD AMD-761, Software/Bios Design Manual

The AMD AMD-761 Software/Bios Design Manual is a comprehensive and informative guide that provides users with detailed instructions on optimizing and configuring their AMD-761 motherboard. This manual can be easily downloaded for free from manualshive.com, allowing users to enhance their system's performance effortlessly.

Share
Download
background image

Chapter 2

AMD-761™ System Controller  Programmer’s Interface

87

24081D—February 2002 

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

Programming Notes

Bit Definitions

GART/AGP Mode Control (Dev0:F0:0xB0)

Bit

Name

Function

31–21

Reserved

Reserved

20

Reserved

19

NonGART_Snoop

NonGART Snoop

When set, this bit forces AGP accesses that are not in the GART range to cause
AMD Athlon™ processor system bus probes to the processor(s). When clear, AGP
addresses that fall outside of the GART range do not cause probes.

18

Reserved

17

PDC_En

Gart Page Directory Cache Enable

This bit is used only in the two-level GART mode. It has no effect in the one-level GART
mode. The GART directory is enabled only when both this bit and the AGP Features
Control register (offset 02h of the memory-mapped Features and Capabilities register—see
“Bar1 + 0x00” on page 141) bit 2, "GART Cache Enable", are 1s. 

16

Lv1_Index

Level 1 Index (GART Index Scheme Control)

When set to 1, this bit enables the one-level GART mode. When cleared to 0, two-level
GART mode is enabled.

15–0

Reserved

Reserved

Summary of Contents for AMD-761









































































































































































































































































Reviews:

No comments

Related manuals for AMD-761

Valve Concepts 5400 Installation, Operation And Maintenance Manual preview
5400
Brand: Valve Concepts Pages: 16
FAAC 740 D Manual preview
740 D
Brand: FAAC Pages: 14
Haier YR-H71 Service Manual preview
YR-H71
Brand: Haier Pages: 58
KEENZ Class Instruction Manual preview
Class
Brand: KEENZ Pages: 24
DAVIS 6830 User Manual preview
6830
Brand: DAVIS Pages: 8
Jafar 3500 Operating Manual preview
3500
Brand: Jafar Pages: 9
Samsung SPC-6000 Quick Setup Manual preview
SPC-6000
Brand: Samsung Pages: 6
Samsung MWR-WE10N Manual preview
MWR-WE10N
Brand: Samsung Pages: 32
Gardena 4030 Operating Instructions Manual preview
4030
Brand: Gardena Pages: 17
SAFI DN15 Manual preview
DN15
Brand: SAFI Pages: 18
Badger Meter Orion Series Quick Start Manual preview
Orion Series
Brand: Badger Meter Pages: 2
Badger Meter MDS 2000 Installation And Software Manual preview
MDS 2000
Brand: Badger Meter Pages: 48
Badger Meter BadgerTouch HREBT Manual preview
BadgerTouch HREBT
Brand: Badger Meter Pages: 12
Badger Meter CB-30 User Manual preview
CB-30
Brand: Badger Meter Pages: 16
Balmar Max Charge MC-624 Installation And Operator'S Manual preview
Max Charge MC-624
Brand: Balmar Pages: 8
Balmar MAX CHARGE MC-614 Installation And Operation Manual preview
MAX CHARGE MC-614
Brand: Balmar Pages: 20
Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
FAAC E124 Manual preview
E124
Brand: FAAC Pages: 32

Brands by name

Popular brands

Load more brands