AMD AMD-761 Software/Bios Design Manual Download Page 147

Page: 147 / 264

Chapter 2

AMD-761™ System Controller Programmer’s Interface

135

24081D—February 2002

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

AGP/PCI Interrupt and Bridge Control

Dev1:0x3C

Register Description

Bit

Reserved

Reset

R/W

Bit

Bridge_Fast

_B2B_En

Secon_Bus

_Reset

Mas_Abort

_Mode

Reserved

VGA_En

ISA_En

SERR_En

Par_Resp_En

Reset

R/W

Bit

Int_Pin

Reset

R/W

R/W (See Note)

Bit

Int_Line

Reset

R/W

Bit Definitions

AGP/PCI Interrupt and Bridge Control (Dev1:0x3C)

Bit

Name

Function

31–24

Reserved

Reserved

Bridge_Fast_
B2B_En

Fast Back-to-Back Capable

This bit is always 0, indicating that the AMD-761™ system controller as a master is not
capable of generating fast back-to-back transactions to different agents on the
secondary bus.

Secon_Bus_Reset

Secondary Bus Reset

This bit is always 0. Reset for the secondary interface is done with the PCIRST# output of
the AMD-766™ peripheral bus controller.

Mas_Abort_Mode

Master Abort Mode

This bit is always 0. The response to a master abort is determined by the
RD_Data_Err_Dis bit, Dev0:F0:0x84 bit 12.

Summary of Contents for AMD-761









































































































































































































































































Search results

Summary of Contents for AMD-761

Reviews:

AMD AMD-761, Software/Bios Design Manual, Page: 147 / 264

Search results

Summary of Contents for AMD-761

Reviews: