manualshive.com logo in svg

AMD AMD-761, Software/Bios Design Manual

The AMD AMD-761 Software/Bios Design Manual is a comprehensive and informative guide that provides users with detailed instructions on optimizing and configuring their AMD-761 motherboard. This manual can be easily downloaded for free from manualshive.com, allowing users to enhance their system's performance effortlessly.

Share
Download
background image

Chapter 4

Power Management

187

24081D—February 2002 

AMD-761™ System Controller Software/BIOS Design Guide

Preliminary Information

The first option is the recommended mode and requires no
special setup in the AMD-761 system controller other than to
write a 0 to the Halt_Discon_En bit in the BIU Status/Control
register (Dev 0:F0:0x60, bit 18). This action causes the
AMD-761 system controller to react to the Halt special cycle on
the AMD Athlon system bus by forwarding the cycle to the PCI
bus but not attempting any processor disconnect. There is no
significant power savings in this mode.

The second option requires that the Halt_Discon_En bit be set,
which forces the AMD-761 system controller to initiate a
p r o c e s s o r   d i s c o n n e c t   f o r   l o w e r   p o w e r   u s i n g   t h e
PROCRDY/CONNECT protocol on the AMD Athlon™ system
bus. The PCI and AGP arbitration remains enabled in this
state, thus any DMA cycles that require a probe of the
processor’s cache causes the AMD-761 system controller to
reconnect using the PROCRDY/CONNECT protocol. There is
some additional latency imposed when this mode is enabled,
because each processor probe requires a reconnect of the CPU.
When the AMD Athlon system bus is disconnected, the
processor enters a very low-power state.

The AMD-766™ peripheral bus controller Southbridge does not
require any special initialization for either of the above
two modes.

4.2

C2 Stop Grant State Requirements

The processor enters the C2 Stop Grant state and issues a Stop
Grant special cycle on the AMD Athlon processor system bus in
response to the assertion of the STPCLK# input signal by the
Southbridge. The AMD-761 system controller supports two
options for the Stop Grant state:

1. Wait for a Stop Grant Special Cycle from both installed

processors and fForward the Stop Grant special cycle to the
PCI bus, but otherwise continue normal operation (no
significant processor power savings).

2. Disconnect the processor, enter self-refresh, and then

forward the Stop Grant special cycle to the PCI bus. This
power management state provides a lower power clock

Summary of Contents for AMD-761









































































































































































































































































Reviews:

No comments

Related manuals for AMD-761

zipwake S Series Troubleshooting Manual preview
S Series
Brand: zipwake Pages: 12
Watts 7 Series Installation, Maintenance & Repair preview
7 Series
Brand: Watts Pages: 2
jbc UCR Instruction Manual preview
UCR
Brand: jbc Pages: 12
Nelson 800 Series Application Manual preview
800 Series
Brand: Nelson Pages: 19
C-TEC 800 Series Installation Instructions preview
800 Series
Brand: C-TEC Pages: 2
Falcon RS500 Owner'S And Installer'S Manual preview
RS500
Brand: Falcon Pages: 3
OBaby Cobra Instructions For Use Manual preview
Cobra
Brand: OBaby Pages: 47
Wasp B2000 Installation Manual preview
B2000
Brand: Wasp Pages: 16
ABB HF Series Manual preview
HF Series
Brand: ABB Pages: 63
UniKey SR3 Installation Manual & User Manual preview
SR3
Brand: UniKey Pages: 20
Eaton A201 Instruction Leaflet preview
A201
Brand: Eaton Pages: 6
DayTronic 3700 Series Instruction Manual preview
3700 Series
Brand: DayTronic Pages: 22
DayTronic System 10 User Manual Book preview
System 10
Brand: DayTronic Pages: 414
GEA VARIVENT D Series Operating Instruction preview
VARIVENT D Series
Brand: GEA Pages: 78
GEA T-smart 7 Operating Instruction preview
T-smart 7
Brand: GEA Pages: 96
GEA T.VIS P-15 Operating Instruction preview
T.VIS P-15
Brand: GEA Pages: 66
UNI EV Series Operating And Mounting Manual preview
EV Series
Brand: UNI Pages: 21
OBSIDIAN CONTROL SYSTEMS NX4 Installation Manual preview
NX4
Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brands by name

Popular brands

Load more brands