manualshive.com logo in svg

AMD AMD-761, Software/Bios Design Manual, Page: 160 / 264

Share
Download
AMD AMD-761 Software/Bios Design Manual Download Page 160

148

AMD-761™ System Controller  Programmer’s Interface

Chapter 2

AMD-761™ System Controller Software/BIOS Design Guide

24081D—February 2002 

Preliminary Information

Programming Notes

Bit Definitions

GART Table Cache Entry Control (Bar1 + 0x10)

Bit

Name

Function

31–12

GART_Tbl_Entry
_Addr

GART Table Entry Address

These bits define the page address for the particular GART table entry to be invalidated or
updated. When a page address is written to this register by the AMD-761™ miniport
driver, the referenced GART table cache entry is invalidated or updated based on the value
in bits [1:0] as long as it is within the virtual address space. If the page address is outside of
the virtual address space, then the invalidate/update instructions do nothing.

11–2

Reserved

Reserved

1

Tbl_Update

Table Update

When set, this bit forces the AMD-761 system controller to update the GART table cache
entry specified in bits [31:12] with the current entry in the GART table in system memory.
The update function is performed immediately following the write to this register. When
the update operation is completed, this bit is reset to 0.

0

Tbl_Inval_Entry

Table Invalidate Entry

When set, this bit forces the AMD-761 system controller to invalidate the GART table cache
entry specified in bits [31:12] if it is present in the GART cache. The invalidate function is
performed immediately following the write to this register. When the invalidate operation
is completed, this bit is reset to 0. Note that this bit does not affect the GART
directory cache.

Summary of Contents for AMD-761









































































































































































































































































Reviews:

No comments