Amazone GreenDrill GD200-E Operating Manual Download Page 44

Page: 44 / 106

Implement settings before initial operation

GreenDrill BAH0108-0 03.20

5.3

Replacing the seeding shaft

1. Switch off the control terminal.

2. Empty the seed hopper.

3. Remove the protective cover (1).

3.1 Loosen and remove the 2 hexagonal

nuts (2) with the socket wrench (3).

4. Remove the round belt (1).

5. Release the knurled nuts (2).

6. Remove the cover and pull out the seeding

shaft (1).

7. Refer to the seeding table for the required

seed metering wheels (see section 9,

page

95).

The seeding shaft is installed in the reverse
sequence.

The existing seeding shaft can be
reinstalled after converting the seed
metering wheels. It is more
convenient to install a second
seeding shaft that is already
equipped with the required seed
metering wheels.

Summary of Contents for GreenDrill GD200-E











































































































Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands

Amazone GreenDrill GD200-E, Operating Manual

Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands