Amazone GreenDrill GD200-E Operating Manual Download Page 23 | Manualshive

Page: 23 / 106

background image

General Safety Instructions

GreenDrill BAH0108-0 03.20

23

2.14.5

Cleaning, maintenance and repair



Only carry out cleaning, maintenance and repair work on the implement when:



the control terminal is switched off.



the implement plug is disconnected from the tractor



the drive is switched off.



the tractor engine is at a standstill



the ignition spanner has been removed.



Regularly check the nuts and bolts for a firm seat and retighten them as necessary.



Secure the raised implement or raised implement parts against unintentional lowering before
performing any cleaning, maintenance or repair work on the implement.



When replacing work tools with blades, use suitable tools and gloves.



Dispose of oils, greases and filters in the appropriate manner.



Disconnect the cable to the tractor generator and battery before performing electrical welding
work on the tractor and mounted implements.



Spare parts must at least comply with the specified technical requirements of AMAZONEN-
WERKE. This is ensured through the use of genuine AMAZONE spare parts.

«
...
21
22
23
24
25
...
»

Summary of Contents for GreenDrill GD200-E











































































































Reviews:

No comments

Related manuals for GreenDrill GD200-E

Brand: Cadman Pages: 66

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: Kärcher Pages: 88

Brand: S.R.Smith Pages: 8

Brand: S.R.Smith Pages: 23

NavBoard ZipFlip

Brand: S&S Precision Pages: 6

Brand: Waterpik Pages: 2

Brand: WaterUps Pages: 2

Brand: Yamaha Pages: 45

Brand: GE Pages: 37

Brand: A.J.Antunes Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands