Amazone GreenDrill GD200-E Operating Manual Download Page 52

Page: 52 / 106

GreenDrill control terminal 5.2

GreenDrill BAH0108-0 03.20

6.1

Control elements

(1) Graphic display

(2) On/Off button

(3) The control lamp is illuminated

when the control terminal is switched on

(4) Switch the electric fan drive

on and off.

The button is without function with
the hydraulic fan drive.

(5) The control lamp is illuminated

when the fan is switched on.

(6) Switch seeding shaft on/off

(7) The control lamp is illuminated

when the seeding shaft is running

(8) Increase seeding shaft speed

(9) Decrease seeding shaft speed

(10) Cursor key

(moves up in the menu)

(11) Cursor key

(moves down in the menu)

(12) Button for confirming the selection

Summary of Contents for GreenDrill GD200-E











































































































Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands

Amazone GreenDrill GD200-E, Operating Manual

Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands