Amazone GreenDrill GD200-E Operating Manual Download Page 26

Page: 26 / 106

Product description

GreenDrill BAH0108-0 03.20

3.2

Technical data

Catch crop seed drill

GreenDrill

GD200-E

GreenDrill

GD200-H

GreenDrill

GD500-H

GreenDrill

GD500-D

Seed hopper volume [l]

200

500

Outlets [number]

Fan drive

Electric

hydraulic

from the

carrying

implement

Metering unit

Metering with electrical metering motor

Automatic
seed rate control when
changing speed

A connection from the control terminal 5.2 to the 7-pin signal
socket of the tractor or the radar or GPS device is required.

Seed placement

via baffle plate

3.3

Rating plate and CE mark

The figure shows the arrangement of the rating
plate (1) and the CE mark (2) on the implement.

The CE mark indicates compliance with the
stipulations of the valid EU directives.

The following information is specified on the
rating plate and the CE mark:

(1) Implement ID no.

(2) Product

(3) Basic weight (kg)

(4) Perm. system pressure total weight kg

(5) Factory

(6) Model year

(7) Year of manufacture

Summary of Contents for GreenDrill GD200-E











































































































Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands

Amazone GreenDrill GD200-E, Operating Manual

Search results

Summary of Contents for GreenDrill GD200-E

Reviews:

Related manuals for GreenDrill GD200-E

Brands by name

Popular brands