Alvarado SW1000 Assembly, Installation And Operation Instructions Download Page 9

Page: 9 / 42

SW1000 Installation and Operation Instructions

PUD3448R2-1

For Assistance: [email protected] +1 (909) 591-8431

Page 9

Installation Tools

•  Hammer Drill
•  5/8" Concrete Drill Bit
•  Pencil
•  Shop Vac

•  Rubber Mallet
•  Torque Wrench (in-lbs.)
•  Torque Wrench (ft-lbs.)
•  9/16" Socket

•  Straight Edge Level
•  #2 Phillips Head Screwdriver
•  Clear RTV Silicone
•  Allen Wrenches: 3/32", 5/32",

5/64", 1/4"

This product is shipped with all installation hardware and components. Make sure that none of these parts are missing

and/or damaged before beginning installation. If parts are missing and/or damaged, please contact Alvarado Technical

Support at (909) 591-8431.

Also Included:

Parts List

•

(4) Concrete Anchor Package (Qty 1)

•

Barrier Clamp Screws (Qty 4)

•

Barrier Plate Screws (Qty 4)

•

Top Cover Screws (Qty 3)

•

Access Panel Screws (Qty 2)

•

SW1000 Utility CD (Qty 1)

Base Plate

(Qty 1)

Access Panel

(Qty 1)

Barrier Clamp

(Qty 1)

Barrier Plate

(Qty 1)

Lid

(Qty 1)

Tower Assembly

(Qty 1)

Barrier

(Qty 1)

Lower Cover

(Qty 1)

Upper Cover

(Qty 1)

Refer to Appendix A for information and instructions

specific to SW1000T tandem gate installations.

NOTE

Summary of Contents for SW1000











































Search results

Summary of Contents for SW1000

Reviews:

Related manuals for SW1000

Brands by name

Popular brands

Alvarado SW1000, Assembly, Installation And Operation Instructions

Search results

Summary of Contents for SW1000

Reviews:

Related manuals for SW1000

Brands by name

Popular brands