manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Administration Manual

The Altigen AltiWare ACC 5.1 Administration Manual is an essential guide for users looking to efficiently manage their Altigen AltiWare ACC 5.1 system. This comprehensive manual provides step-by-step instructions and in-depth information, ensuring seamless operation. Available as a free download from manualshive.com, users can easily access this valuable resource.

Share
Download
background image

122

AltiWare ACC 5.1 Administration Manual

Incoming Ring 
Type

Single—Default setting for North America
Double—For countries using Ring-Ring-Silent type of ring 
pattern

Centrex Flash 
Duration (ms)

Specifies the Flash Duration time in milliseconds, with a range 
from 50 ms to 1000 ms. This setting complements the Centrex 
Flash Support option in the General tab for the trunk.

Detect Trunk 
Status By Loop 
Current

When selected, the analog trunk will check the loop current 
and if connected will change the state to “Idle.” If not selected, 
the trunk will check circuit DC voltage to determine the trunk 
status. Do not change this setting without consulting with 
AltiGen Technical Support.

Enable Caller ID 
Receive

When selected, the system will wait for caller ID FSK signal 
before answering the incoming call. In North America, 
typically it takes two rings to receive the caller ID from the CO. 
If your trunk does not have caller ID service, you can uncheck 
this box to speed up the answering process.

Out of Service With 
Trunk Seizure

When checked, if the trunk is set to Out of Service, the system 
will busy out the trunk. The CO will treat this trunk as a busy 
line and WILL NOT place a call to this trunk. (By default, this 
option is unchecked.)

Call Setup

Select from:

•

Enable Dial Tone Detection (Outgoing)—When 
enabled, the trunk channel must detect outgoing dial tone 
prior to making the call.

•

Enable Answer Debounce (Incoming)—Enables a 
timeout period of 2 seconds (for ignoring false CO 
disconnect signal), after answering an incoming call.

Disconnect 
Supervision

Select from:

•

Tone—busy tone (reorder tone, fast busy tone, error tone, 
and so on) or dial tone (continuous tone, and so on). This 
should be used in conjunction with drop in loop current. For 
COs who cannot guarantee loop break, this may be the only 
option.

•

Polarity Reversal—a reversed battery signal. 
Loop Break Signal either 200 or 600. 600 ms is common 
in North America.

Receive from CO 
(dB Gain)

Slide setting adjusts the gain from the CO to the trunk from 
0 dB to 7 dB for every Quantum Trunk channel.
The default setting is 

0 dB

, and it is highly recommended not 

to change this setting.
Caution! Setting the volume too high will cause distortion in 
voice quality and/or missed DTMF digits.

Parameter

Description

Summary of Contents for AltiWare ACC 5.1
































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare ACC 5.1

FARONICS POWER SAVE MAC Getting Started Manual preview
POWER SAVE MAC
Brand: FARONICS Pages: 5
FARONICS POWER SAVE Product Data Sheet preview
POWER SAVE
Brand: FARONICS Pages: 2
FARONICS DEEP FREEZE ENTERPRISE Getting Started Manual preview
DEEP FREEZE ENTERPRISE
Brand: FARONICS Pages: 3
FARONICS ANTI-EXECUTABLE ENTERPRISE Getting Started Manual preview
ANTI-EXECUTABLE ENTERPRISE
Brand: FARONICS Pages: 2
Yamaha CL1 Owner'S Manual preview
CL1
Brand: Yamaha Pages: 89
Canon PowerShot A590 IS Software User'S Manual preview
PowerShot A590 IS
Brand: Canon Pages: 49
Yamaha MOTIF XF Owner'S Manual preview
MOTIF XF
Brand: Yamaha Pages: 11
Alcatel Genesys 7.5 Course Information preview
Genesys 7.5
Brand: Alcatel Pages: 2
SSI TROPOS SUPERSEARCH 2.4.0.000 Installation Manual preview
TROPOS SUPERSEARCH 2.4.0.000
Brand: SSI Pages: 8
GRASS VALLEY EDIUS User Reference Manual preview
EDIUS
Brand: GRASS VALLEY Pages: 790
TYAN AST2050 User Manual preview
AST2050
Brand: TYAN Pages: 41
Oracle Retail Data Warehouse Installation Manual preview
Retail Data Warehouse
Brand: Oracle Pages: 35
Oracle Oracle7 Server 7.3 Getting Started Manual preview
Oracle7 Server 7.3
Brand: Oracle Pages: 202
KAPERSKY ANTI-VIRUS 5.5 - FOR CHECK POINT FIREWALL-1 Administrator'S Manual preview
ANTI-VIRUS 5.5 - FOR CHECK POINT FIREWALL-1
Brand: KAPERSKY Pages: 141
National Instruments Instrument Driver NI-DMM Quick Reference preview
Instrument Driver NI-DMM
Brand: National Instruments Pages: 12
TANDBERG MOVI 4.0 - FOR WINDOWS 09-2010 User Manual preview
MOVI 4.0 - FOR WINDOWS 09-2010
Brand: TANDBERG Pages: 19
Xerox DocuShare 6.0 User Manual preview
DocuShare 6.0
Brand: Xerox Pages: 20
TC Electronic MegaReverb Manual preview
MegaReverb
Brand: TC Electronic Pages: 7

Brands by name

Popular brands

Load more brands