manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Administration Manual, Page: 35 / 383

Share
Download
Altigen AltiWare ACC 5.1 Administration Manual Download Page 35

Chapter 2:  Software Installation & License Registration

AltiWare ACC 5.1 Administration Manual 21

Preparation for Installation

Before you start installing AltiWare, you need the following:

•

Windows Update—Make sure your server has the recommended Windows Service 
Pack or Update.

•

AltiWare 5.1 CD ROM—The AltiWare CD ROM that contains the AltiWare 5.1 
programs.

•

AltiWare latest update—Check to see if there is an Update available to the 
AtliWare 5.1 Release.

•

System Key—The system key is a DB-25 parallel port hardware security device that 
allows the software to run ONLY when that system key is attached to the parallel 
port of the server that AltiWare is running on. (By special order, your system key 
may be a USB key.)

•

Software license key—A 20-digit key located on the front of the End User License 
Agreement. The following table lists all licenses used in AltiWare 5.1.

Table 1. AltiWare ACC/ACM 5.1 License Summary

License 

Type

License 

Model

Supported AltiWare Software Version

ACC 5.1

ACM 5.1

Server Base 
License

Per System

•

Fresh Install

•

Upgrade

•

Upgrade

•

Migrate

Station License

Per Activated 

Extension

YES

YES

Agent Seat

Per concurrent login
(Single agent 
logged into multiple 
WGs will only take 
one license)

ACC Agent Seat

ACM Agent Seat

AltiView

Per concurrent login

YES

YES

AltiConsole

Per concurrent login

YES

YES

AltiAgent

Per concurrent login

YES

YES

AltiSupervisor

Per concurrent login

YES

YES

IPTalk

Per concurrent login

YES

YES

SIP Trunk

Per activated SIP 

trunk

YES

YES

Centralized 
Recording

Per Session

NO

YES

Advanced Call 
Router

Per System

NO

YES

AltiReport

Per System

NO

YES

VRManager

Per System

NO

YES

AltiWeb

Per System

NO

YES

SDK

Per Session

NO

YES

Summary of Contents for AltiWare ACC 5.1
































































































































































































































































































































































































Reviews:

No comments