manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Administration Manual, Page: 137 / 383

Share
Download
Altigen AltiWare ACC 5.1 Administration Manual Download Page 137

AltiWare ACC 5.1 Administration Manual 99

C

H A P T E R

6

Trunk Configuration

Trunk attributes and parameters are set using the Trunk Configuration window. The 
attributes and options available depend on the type of board and trunk. This chapter 
discusses general configuration options applicable to all trunks, followed by specific 
configuration options for the following trunk types:

•

H.323 tie trunk, page 106

•

SIP tie trunk, page 106

•

SIP trunk for ITSP, page 107

•

Triton T1/PRI trunk, page 109

•

Triton analog trunk, page 112

•

Quantum trunk, page 121

This chapter also discusses incoming call routing (page 121) and outgoing call blocking 
(page 124), both configurable on tabs in the Trunk Configuration window.

Trunks Out of Service

If none of the trunks are available when an outside call is placed, the caller will hear the 
system prompt: “All outside lines are busy. Please try again later.”

Channel Identification

To find out channel information, right-click a trunk in the Trunk View window (shown in 
Figure 2, below), and select Channel Physical Location. The Channel Information box 
appears, displaying logical board ID, board name, channel group type, and channel ID.

Summary of Contents for AltiWare ACC 5.1
































































































































































































































































































































































































Reviews:

No comments