manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Administration Manual, Page: 359 / 383

Share
Download
Altigen AltiWare ACC 5.1 Administration Manual Download Page 359

Appendix A:  E1-R2 and E1 ISDN PRI Installations

AltiWare ACC 5.1 Administration Manual 331

E1 ISDN PRI Installation

This section describes the configuration procedures necessary to implement E1 ISDN PRI 
signaling for European, Pacific Rim, and other emerging markets. Please carefully follow 
the procedures step by step.
1. Change the Configure Type to E1:

a. From Boards view, double-click the board to be configured to open the Board 

Configuration window. 

b. In the Board Configuration window, click the Board Configuration button.  

Venezuela / Nacional 
MFC-R2

Set calling part category: 1
[Assume no caller ID provided]: 
Incoming sequence: DID/DNIS
In-call signaling (depend on how many DID digits): 
For 3-digit DID, set to (113)6
For 4-digit DID, set to (1113)6
For 5-digit DID, set to (11113)6
For 6-digit DID, set to (111113)6
For 7-digit DID, set to (1111113)6
For 8-digit DID, set to (11111113)6
[Assume caller ID provided]: 
Incoming sequence (same as above shown):
DID/DNIS  *  Caller ID
In-call signaling (depend on how many DID digits) : 
For 3-digit DID, set to (115)*(K)36
For 4-digit DID, set to (1115)*(K)36
For 5-digit DID, set to (11115)*(K)36
For 6-digit DID, set to (111115)*(K)36
For 7-digit DID, set to (1111115)*(K)36
For 8-digit DID, set to (11111115)*(K)36

Country

Signaling Values

Summary of Contents for AltiWare ACC 5.1
































































































































































































































































































































































































Reviews:

No comments