manualshive.com logo in svg

Altigen AltiWare ACC 5.1, Administration Manual, Page: 119 / 383

Share
Download
Altigen AltiWare ACC 5.1 Administration Manual Download Page 119

Chapter 5:  Board Configuration

AltiWare ACC 5.1 Administration Manual 81

You can configure the board type: either T1 or E1 to run T1 CAS, T1 PRI, or E1 CAS, 
E1 PRI. Additional steps are needed to further configure the CAS or PRI protocol in 
the Protocol Configuration window, shown in Figure 9 and Figure 10. 

Figure 6. Triton T1/E1 Configuration dialog box 

(For information on adding and removing mobile trunks, see “Mobile Extension 
Configuration” on page 239.)

T1 and E1 Configuration

Double-clicking a channel group for a Triton T1 board in the Channel Group Info pane 
opens a T1 or E1 Configuration dialog box, as in Figure 7 and Figure 8.

Figure 7. Triton T1 configuration dialog box

Summary of Contents for AltiWare ACC 5.1
































































































































































































































































































































































































Reviews:

No comments