Altera Arria 10 Avalon-ST Interface User Manual Download Page 91

Page: 91 / 147

Bits

Register Description

Value

Access

[31:0]

JTAG Silicon ID DW0

. This is the JTAG Silicon ID that CvP

programming software reads to determine that the correct SRAM

object file (.sof) is being used.

Application

Specific

Table 7-6: User Device or Board Type ID Register

Bits

Register Description

Value

Access

[15:0]

Configurable device or board type ID to specify to CvP the

correct .sof.

Variable

CvP Registers

Table 7-7: CvP Status

The

CvP Status

Bits

Register Description

Reset Value

Access

[31:26]

Reserved

0x00

[25]

PLD_CORE_READY

. From FPGA fabric. This status bit is

provided for debug.

Variable

[24]

PLD_CLK_IN_USE

. From clock switch module to fabric. This

status bit is provided for debug.

Variable

[23]

CVP_CONFIG_DONE

. Indicates that the FPGA control block has

completed the device configuration via CvP and there were

no errors.

Variable

[22]

Reserved

Variable

[21]

USERMODE

. Indicates if the configurable FPGA fabric is in user

mode.

Variable

[20]

CVP_EN

. Indicates if the FPGA control block has enabled CvP

mode.

Variable

[19]

CVP_CONFIG_ERROR

. Reflects the value of this signal from the

FPGA control block, checked by software to determine if

there was an error during configuration.

Variable

[18]

CVP_CONFIG_READY

. Reflects the value of this signal from the

FPGA control block, checked by software during

programming algorithm.

Variable

[17:0]

Reserved

Variable

7-10

CvP Registers

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Registers

Send Feedback

Summary of Contents for Arria 10 Avalon-ST Interface




















































































































































Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands

Altera Arria 10 Avalon-ST Interface, User Manual

Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands