Altera Arria 10 Avalon-ST Interface User Manual Download Page 33

Page: 33 / 147

Interface Type

Minimum

Low

Balanced

High

Maximum

Avalon-MM with

DMA

Available

Not Available

Avalon-ST with SR-

IOV

Available

Related Information

•

PCI Express Base Specification 3.0

•

Arria 10 Transceiver PHY User Guide

Provides information about the ADME feature for Arria 10 devices.

Arria 10 Avalon-MM Settings

Table 4-3: Avalon Memory-Mapped System Settings

Parameter

Value

Description

Avalon-MM address

width

32-bit
64-bit

Specifies the address width for Avalon-MM RX master ports

that access Avalon-MM slaves in the Avalon address

domain. When you select 32-bit addresses, the PCI Express

Avalon-MM DMA bridge performs address translation.

When you specify 64-bits addresses, no address translation is

performed in either direction. The destination address

specified is forwarded to the Avalon-MM interface without

any changes.
For the Avalon-MM interface with DMA, this value must be

set to 64.

Enable control

register access

(CRA) Avalon-MM

slave port

On/Off

Allows read and write access to bridge registers from the

interconnect fabric using a specialized slave port. This

option is required for Requester/Completer variants and

optional for Completer Only variants. Enabling this option

allows read and write access to bridge registers, except in the

Completer

Only single dword variations.

Export MSI/MSI-X

conduit interfaces

On/Off

When you turn this option On, the core exports top

level

MSI and MSI

X interfaces that you can use to implement a

Custom Interrupt Handler for MSI and MSI

X interrupts.

For more information about the Custom Interrupt Handler,

refer to

Interrupts for End Points Using the Avalon-MM

Interface with Multiple MSI/MSI

X Support

. If you turn this

option Off, the core handles interrupts internally.

4-4

Arria 10 Avalon-MM Settings

UG-01145_avmm_dma

2015.11.02

Altera Corporation

Parameter Settings

Send Feedback

Summary of Contents for Arria 10 Avalon-ST Interface




















































































































































Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands

Altera Arria 10 Avalon-ST Interface, User Manual

Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands