Altera Arria 10 Avalon-ST Interface User Manual Download Page 108

Page: 108 / 147

Control Register Access (CRA) Avalon-MM Slave Port

Table 7-19: Configuration Space Register Descriptions

The optional CRA Avalon-MM slave port provides host access to selected Configuration Space and status

registers. These registers are read only. For registers that are less than 32 bits, the upper bits are unused.

Byte Offset

Register

Dir

Description

14'h0000

cfg_dev_ctrl[15:0]

cfg_devctrl[15:0]

is device control for the PCI

Express capability structure.

14'h0004

cfg_dev_ctrl2[15:0]

cfg_dev2ctrl[15:0]

is device control 2 for the

PCI Express capability structure.

14'h0008

cfg_link_ctrl[15:0]

is the primary Link Control

of the PCI Express capability structure.
For Gen2 or Gen3 operation, you must write a 1’b1

to Retrain Link bit (Bit[5] of the

cfg_link_ctrl)

the Root Port to initiate retraining to a higher data

rate after the initial link training to Gen1 L0 state.

Retraining directs the LTSSM to the Recovery state.

Retraining to a higher data rate is not automatic

even if both devices on the link are capable of a

higher data rate.

14'h000C

cfg_link_ctrl2[15:0]

cfg_link_ctrl2[31:16]

is the secondary Link

Control register of the PCI Express capability

structure for Gen2 operation.
When

tl_cfg_addr=2

tl_cfg_ctl

returns the

primary and secondary Link Control registers,

{cfg_link_ctrl[15:0], cfg_link_

ctrl2[15:0]}

, the primary Link Status register

contents is available on

tl_cfg_sts[46:31]

For Gen1 variants, the link bandwidth notification

bit is always set to 0.For Gen2 variants, this bit is set

to 1.

14'h0010

cfg_prm_cmd[15:0]

Base/Primary Command register for the PCI

Configuration Space.

14'h0014

cfg_root_ctrl[7:0]

Root control and status register of the PCI-Express

capability. This register is only available in Root

Port mode.

UG-01145_avmm_dma

2015.11.02

Control Register Access (CRA) Avalon-MM Slave Port

7-27

Registers

Altera Corporation

Send Feedback

Summary of Contents for Arria 10 Avalon-ST Interface




















































































































































Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands

Altera Arria 10 Avalon-ST Interface, User Manual

Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands