Altera Arria 10 Avalon-ST Interface User Manual Download Page 61

Page: 61 / 147

Signal Name

Direction

Description

TxsWaitRequest_o

Output

When asserted, indicates that the Avalon-MM slave port is not

ready to respond to a read or write request.

Figure 6-6: TX Slave Interface Sends Status to Host

AvTxsChipSelect_i

AvTxsWrite_i

AvTxsAddress_i[27:0]

AvTxsByteEnable_i[3:0]

AvTxsWriteData_i[31:0]

AvTxsWaitRequest_o

AvTxsRead_i

AvTxsReadData_o[31:0]

AvTxsReadDataValid_o

32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave Signals

The CRA port provides host access to the status registers of the Avalon-MM DMA bridge.

Table 6-5: Avalon-MM CRA Slave Interface Signals

Signal Name

Direction

Description

CraRead_i

Input

Read enable

CraWrite_i

Input

Write request

CraAddress_i[13:0]

Input

An address space of 16 KB is allocated for the control registers.

Avalon-MM slave addresses provide address resolution down

to the width of the slave data bus. Because all addresses are

byte addresses, this address logically goes down to bit 2. Bits 1

and 0 are 0. To read or write individual bytes of a dword, use

byte enables. For example, to write bytes 0 and 1, set

CraByteEnable_i[3:0]= 4'b0011

6-8

32-Bit Non-Bursting Avalon-MM Control Register Access (CRA) Slave...

UG-01145_avmm_dma

2015.11.02

Altera Corporation

IP Core Interfaces

Send Feedback

Summary of Contents for Arria 10 Avalon-ST Interface




















































































































































Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands

Altera Arria 10 Avalon-ST Interface, User Manual

Search results

Summary of Contents for Arria 10 Avalon-ST Interface

Reviews:

Related manuals for Arria 10 Avalon-ST Interface

Brands by name

Popular brands