51
-EN
3
Touch
[
]
or
[
]
of the desired MX mode.
•
Music source (such as CDs, iPod, etc.) level can be set.
MX CD (OFF, CD MX 1 to 3)
CD mode processes a large quantity of data. This data is used
to reproduce the sound cleanly by making use of the data
quantity.
MX CMPM (OFF, CMPM MX 1 to 3)
This corrects information that was omitted at the time of
compression. This reproduces a well-balanced sound close to
the original.
MX DVD (OFF, Movie MX 1 to 2)
The dialogue portion of the video is reproduced more clearly.
MX AUX (OFF, CMPM MX, Movie MX, Music MX)
Choose the MX mode (CMPM, Music, or Movie) that
corresponds to the media connected.
•
When OFF is selected, MX effect of each MX mode will be OFF.
•
Each music source, such as CD, and MP3 can have its own MX
setting.
•
MX mode does not function when MX is ON for FM, MW, LW radio.
•
MX CMPM is applied for MP3/WMA/AAC and iPod/iPhone.
•
The MX setting can be performed only when a source is currently
selected.
•
This function is inoperable when Defeat is set to ON.
Before performing the following procedures, refer to “About the
Crossover” (page 55).
Setting item : X-Over
1
Touch
[
]
or
[
]
of X-Over to select L/R or L+R.
2
Touch
[
]
of X-Over.
A speaker list on the X-OVER screen is displayed.
3
Touch
[
]
of the band to be adjusted.
The screen changes to the X-Over screen to be adjusted.
4.2ch (FRONT/REAR/SUBW.) System / (L+R)
Setting contents:
Low (SUB-W) / Mid (REAR) / High (FRONT)
4.2ch (FRONT/REAR/SUBW.) System / (L/R)
Setting contents:
Low (SUB-W)-L / Low (SUB-W)-R / Mid (REAR)-L /
Mid (REAR)-R / High (FRONT)-L / High (FRONT)-R
4
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[
]
or
[
]
of Freq., then select the cut-off frequency
(crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
4.2ch (FRONT/REAR/SUBW.) System
Setting contents:
Low (SUB-W)
20 Hz~200 Hz
Mid (REAR)
20 Hz~200 Hz
High (FRONT)
20 Hz~200 Hz
Adjusting the Slope
Touch
[
]
or
[
]
of Slope, then adjust the HPF or LPF slope.
Adjustable slope: FLAT, –6 dB/oct., –12 dB/oct., –18 dB/oct.,
–24 dB/oct.
Adjusting the Level
Touch
[
]
or
[
]
of Level, then adjust the HPF or LPF level.
Adjustable output level: -12 to 0 dB.
5
Repeat steps 3 to 4 to make adjustment to the other
bands.
2.2ch (3WAY) System / (L+R)
Setting contents:
Low / Mid-L / Mid-H / High
2.2ch (3WAY) System / (L/R)
Setting contents:
Low-L / Low-R / Mid-L-L / Mid-L-R / Mid-H-L /
Mid-H-R / High-L / High-R
4
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch
[
]
or
[
]
of Freq., then select the cut-off frequency
(crossover point).
The adjustable bandwidth differs depending on the speaker
(channel).
2.2ch (3WAY) System
Setting contents:
Low / Mid-L
20 Hz~200 Hz
Mid-H
20 Hz~20 kHz
High
(1 kHz~20 kHz)
*
1
/(20 Hz~20 kHz)
*
2
*
1
When Factory’s is selected, refer to “Setting the Response Slope for
the High Range Speaker (TW Setup)” (page 53).
*
2
When User’s is selected, refer to “Setting the Response Slope for the
High Range Speaker (TW Setup)” (page 53).
(DVD Music)
This disc contains a large quantity of data such as music clip.
MX uses this data to reproduce the sound accurately.
Adjusting the Crossover Settings (X-Over)
L/R:
Different adjustment values can be set for the left and
right channels.
L+R:
Sets the same adjustment values for the left and right
channels.
4.2ch (FRONT/REAR/SUBW.) System
2.2ch (3WAY) System
